Overview
- SIMATIC ET 200pro distributed I/O system with IP65/67 degree of protection for cabinet-free use at the machine
- Small, multifunctional complete solution: Digital inputs/outputs, fail-safe modules, motor starters up to 5.5 kW, etc.
- Communication over PROFIBUS or PROFINET
- Mixed arrangement of fail-safe and standard modules in the same station
- Freely selectable connection technique: direct, ECOFAST or M12 7/8″
- Power module for easy implementation of load groups
- Module replacement during operation (hot swapping)
- Easy installation as well as permanent wiring
- Transmission rate for PROFIBUS DP up to 12 Mbps
- Extensive diagnostics: module-specific or channel-specific
- Intelligent motor starters for starting and protection of motors and loads up to 5.5 kW
- Versions: direct and reversing starters – Standard and High Feature
- Fail-safe motor starters
- Fail-safe modules with safety-related signal processing according to PROFIsafe
- Frequency converters
- RFID communication modules
- Pneumatic interface modules
- IO-Link master
Application
SIMATIC ET 200pro is the new modular I/O system with high degree of protection IP65/66/67 for local, cabinetless applications. ET 200pro distinguishes itself through a small frame size and an innovative installation concept. ET 200pro can be optimized and very flexibly adapted to the requirements of the corresponding automation task with respect to the connection method, required I/Os and fieldbus connection. New features such as the integrated PROFIsafe safety technology, the PROFINET interface and the ability to hotswap modules permit it to be used for a wide range of applications.
With the integrated motor starters, conveyor applications can be implemented optimally, or drives of up to 5.5 kW can be controlled without control cabinet.
Design*
The tried and tested separation of module and bus/power connection technology, which has already been used for the ET 200eco, is now also used for the digital and analog expansion modules of the ET 200pro. For the interface module this allows use of the T-functionality for the bus and 24 V power supply, and for the expansion modules it permits pre-wiring of sensor/actuator connections. This permanent wiring allows exactly one electronics module to be hot-swapped in the event of a fault without having to switch off the whole station. It can continue to operate fault-free while the module is being replaced. This ensures very high plant availability. When an electronics component is replaced, the whole I/O wiring can remain on the connecting module and does not have to be marked or removed.
Modules
The modules of the ET 200pro usually have two or three components. Interface and power modules as well as digital and analog expansion modules comprise:
- A bus connector which constitutes the backplane bus of the system
- An electronics module or interface module
- A connection module
A backplane bus module is required for operation of motor starters.
A station is constructed from:
- A rack
- An interface module for PROFIBUS DP
- A connection module for the interface module for PROFIBUS DP
- CM IM DP direct with up to 6 M20 screwed cable glands
- CM IM DP ECOFAST Cu
- CM IM DP M12 7/8″
Or optionally
- One interface module each for PROFINET IO
- A connection module for the PROFINET IO interface module:
- CM IM PN M12 7/8″ S
- CM IM PN M12 7/8″
- CM IM PN 2 x RJ45
- CM IM PN 2 x SCRJ FO
Or optionally
- one CPU or one F-CPU
- Max. 16 expansion modules that can be mounted in stations up to 1 m in width
Expansion modules
The following expansion modules are available:
- Digital I/Os
- Analog inputs
- Analog outputs
- IO connection modules
- CM IO 8 x M8 for digital electronic modules
- CM IO 4 x M12 inverse for digital electronic modules
- CM IO 4x M12 for digital or analog electronic modules
- CM IO 4 x M12 P for digital electronic modules
- CM IO 8x M12 for digital electronic modules
- CM IO 8x M12 P for digital electronic modules
- CM IO 8 x M12 D for digital electronic modules
- CM IO 2 x M12 for digital electronic modules
- CM IO 1 x M23 for digital electronic modules
- Power module electronics
- Connection modules for power modules
- CM PM-E PP (Push Pull)
- CM PM-E directly with up to 2 M20 screwed cable glands
- CM PM-E ECOFAST Cu
- CM PM-E 7/8”
- Fail-safe electronic modules
- Motor starters
- Fail-safe motor starters
- Frequency converters
- RFID communication modules
- Pneumatic interface modules
- IO-Link master
Rack
Two different racks are available for mounting the ET 200pro:
- Narrow rack – The narrow rack supports complete pre-assembly on the workbench by means of two mounting flanges outside of the ET 200pro station.
- Compact rack – When the compact rack is used, the small footprint of the ET 200pro system can be used to best advantage.
Function
The SIMATIC ET 200pro is easily configured with STEP 7. A GSD file is available for interfacing with systems of other manufacturers.
Technical Specifications
General technical specifications | ||
---|---|---|
Electronic modules | Digital inputs/outputs
| |
Analog inputs
| ||
Analog inputs | ||
Connections | M12 and M8 round connector with standard assignment for actuator/sensor | |
Transmission rate, max. | 12 Mbps (PROFIBUS DP), 100 Mbps (PROFINET IO)
| |
Supply voltage | 24 V DC | |
Current consumption of one ET 200pro (internal and encoder supply, non-switched voltage), up to 55 °C, max. | ≤ 5 A
| |
Load current for ET 200pro per incoming supply (IM, PM, switched voltage), up to 55 °C, max. | 10 A | |
For overall configuration with looping through (multiple ET 200pros), up to 55 °C, max. | 16 A (with connecting module, directly) | |
Degree of protection | IP65/66/IP67 for interface, digital and analog modules | |
Material | Thermoplastic (reinforced with glass fiber)
| |
Environmental conditions | ||
Temperature | From -25 °C/0 °C to +55 °C | |
Relative humidity | From 5 to 100% | |
Air pressure | From 795 to 1080 hPa | |
Mechanical stress | ||
Vibration | Vibration test according to IEC 60068, Part 2-6 (sinusoidal) | |
Constant acceleration 5 g, occasionally 10 g for interface, digital and analog modules2 g motor starters
| ||
Shock | Shock test according to IEC 680068 Part 2-27, half-sine, 30 g, 18 ms duration for interface, digital and analog modules15 g, 11 ms duration for motor starters | |
Approvals | UL, CSA or cULus |
Frequently Asked Questions (FAQs)
Build innovative machines faster without costly prototyping with Efficient Motion Control.
With Effective Motion Control, machine builders can easily overcome major challenges and enable faster time-to-market, increased functionality, resolve complex system requirements, and demands for safety and sustainability.
We are Siemens trusted and approved distribution partner.
As a Value Added Reseller in Siemens’ Approved Partner network, Parmley Graham is a proven supplier of a wide range of quality products in the UK and globally.
Find out more how this will benefit you or check Siemens Configurator.